What does f5 mean on washing machine?

What does f5 mean on washing machine?

The F5 error code indicates that the Central Control Unit (main machine control board) detects a temperature sensor resistance that is out of the normal range. The F5 error is normally caused by a failed NTC temperature sensor.

What does e3 mean on a washing machine?

drum overflow

What does f5 and e2 mean on a washing machine?

The F5 E2 alert indicates the washer can’t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area. Also verify there are no clothing items in the way. CLICK HERE to review a video for more information on the F5 E2 code.

What does f5 mean on Whirlpool?

self cleaning mode

What does e2 mean on my washing machine?

water drainage issue

What e2 means?

Elimination Second Order

What is e3 error?

The E3 error code displays when an Abnormal Operation Protection Error has occurred, and activates to protect the unit from damage. This error code will require service.

What is e2 error?

The E2 error is displayed on the CID when the weapon detects that the date/time is off. This can occur if the battery has been left out of the device for an extended period of time or that the device has not been connected to Evidence Sync for an extended period of time.

What does e2 and f6 mean on Maytag washer?

The F6 E2 alert indicates there is issue with the appliance control unit, user interface or associated wiring. Unplug the washer, wait five minutes, then plug back in.

How do I unlock my Maytag washer door?

Reach up along the inside of the front and locate the bottom of the door switch/lock mechanism. Located on the bottom of the door switch/lock mechanism is a tear shaped tab. Gently pull the tab down about 1/4 inch or until a click is heard. The door can now be opened.

What does F5 mean on washing machine?

What does F5 mean on washing machine?

The F5 error code indicates that the central control unit (main machine) detects a temperature sensor resistance outside the normal range. The F5 error is usually caused by a faulty NTC temperature sensor.

How do I clear the error code on my Maytag washer?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

How do I reset the F5 on my Kenmore washer?

The only way to clear the codes is to unplug and let sit, and then plug back in. Then it is good to go again. Various comments online indicate correlation to Water Temperature Sensor or Water Heating element.

What is F5 error code?

The F5 error code indicates that the Central Control Unit (main machine control board) detects a temperature sensor resistance that is out of the normal range. The F5 error is normally caused by a failed NTC temperature sensor.

How do I fix the code on my Kenmore washer?

You will need to remove the power supply to the washer to reset the code.Look for the “Pause/Cancel” button on the washer control panel. Press the “Pause/Cancel” button twice to cancel the wash cycle. Check for kinks in the water supply hose while the washer does not have power.

Does a Kenmore washer have a reset button?

How to Reset a Kenmore Elite HE Washer Press the “Stop” button twice, and then press the “Power” button. Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”). Press the “Start” button to complete the reset process and restart the washing machine.

What does Code F mean on Kenmore washer?

washer control detected a component problem

What does it mean when your washer says F?

The F/dL code indicates a door lock error on the machine. When the door fails to lock to allow the cycle to begin, it attempts to lock itself at least six times before the error appears on the digital display screen. or a faulty door switch.

What is F11 error code?

The infamous and all-too-common F11 error code in these Whirlpool Duet front load washers is a case-in-point. The tech sheet inside the washer says this is a communications error between two control boards: the CCU (central control unit) and MCU (motor control unit).

How do I reset my Kenmore top load washer?

How do I reset my top load washer?Unplug the washer for 1 minute from the electrical outlet.Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.The motor has now been reset and is ready for you to start a cycle.

How do you run a diagnostic on a Kenmore washer?

With the washer in diagnostic mode, follow these steps to display the error code lights:Turn the control dial 1 click clockwise.Press the Start button.Turn the control dial one click clockwise to display the first saved error code.Turn the control dial one click clockwise to display the next error code.

How do I reset my top load washer?

Motor Reset:Unplug the washer for 1 minute from the electrical outlet.Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. The motor has now been reset and is ready for you to start a cycle.

Is there a way to reset a Whirlpool washer?

Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.

How do I reset the control panel on my Whirlpool washer?

If they are, press START / STOP one time. Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.

What would cause a washer to not fill up?

If your washer if not filling, start by making sure the faucet at the water-supply end of the hose is turned on. If you have un-kinked hoses that are tightly attached and with clean screens, and you have good water pressure, the next place to check for a water-filling problem is the water inlet valve.

How do I troubleshoot my Whirlpool washer?

Whirlpool Washing Machine problemsWasher won’t spin.Washer is making loud noise.Washer won’t agitate.Washer won’t drain.Washer vibrating or shaking.Washer fills slowly or will not fill at all.Washer leaking water.Washer won’t start.