ElectroAnswers

Quick Technology Tips

Appliance 

What does e01 mean on a washing machine?

Joe Dassin

What does e01 mean on a washing machine?

E01 there’s an issue with the lock, its wiring or connection to the control board. Check the door is closed properly and the wiring is intact. E02 the machine has failed to fill with water during its allocated time.

How do I fix e1 error on my Brother sewing machine?

The foot controller was pressed (or the start/stop button was pressed if the foot controller is not connected) and the reverse/reinforcement stitch button was pressed while the presser foot is raised. Lower the presser foot lever before continuing the operation.

What is e1 error on treadmill?

An E1 code just means that the console is not getting a reading from the reed switch (Speed Sensor). If the running belt moves for several minutes and then produces the E1 error, this is most commonly a result of the running belt needing lubrication.

What is e6 error?

An E6 error code is a communication error that the inside unit is not able to communicate with the outside unit. This includes the high voltage and low voltage lines.

How do I fix e5 error on treadmill?

The e5 sensor error code means your treadmills console is not receiving a speed signal. So you will need to take the cover off and locate the speed sensor. It could be located next to the front roller. Make sure it is clean.

How do you fix a speed sensor on a treadmill?

How to Fix a Treadmill Speed SensorUnplug the treadmill power cord. Trace the black and white wire leads from the motor to the circuit board below. Lift the motor at the end opposite the front roller pulley to slack the drive belt. Trace the wire lead from the sensor to the circuit board below.Lisää kohteita…

What does e3 mean on a treadmill?

overspeed warning

Where is the reset button on my treadmill?

Find the reset hole on the underside of the console. Plug the treadmill back in to a power outlet, insert a cotton swab or a small piece of plastic into the reset hole and push the “Reset” button.

How do I know if my treadmill needs lubricant?

How do I know when my treadmill needs to be lubricated? The basic rule to follow is that you should be able to touch your deck surface, under the walking belt and feel a slightly waxy or oily coat of lube on the deck. Check under the area where your feet contact the walking belt.

Where is reset button on NordicTrack treadmill?

NordicTrack – Ensure the machine is not in a program or moving. Locate the reset hole/button underneath the console. This will require a Q-tip or such like to press the button. When done the treadmill will perform the reset.

Electronics 

What does E01 mean on a washing machine?

Joe Dassin

What does E01 mean on a washing machine?

E01 there’s an issue with the lock, its wiring or connection to the control board. Check the door is closed properly and the wiring is intact. E02 the machine has failed to fill with water during its allocated time.

What does E01 mean on a Maytag washer?

So you’re exactly right, E01 F09 means you have a drain issue. There is a drain catch inside the washer that you will want to access and clean if you’re getting this drain error. To access the drain catch, tip the machine backwards and lean it against the wall at a 45 degree angle or so.

What does code F01 mean on Whirlpool washer?

failed electronic machine control board

What does error code F01 mean?

Do Whirlpool washers have a reset button?

How to Confirm You Have Reset Your Whirlpool Washing Machine. Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.

How do I put my Whirlpool front load washer in diagnostic mode?

Whirlpool Duet Diagnostic Test ModeClose the washer door.Select any one key except “Stop/Cancel” and Control Lock.Using the same key… If you got it right all the lights on the Duet washer’s control should light up, and any error codes in the washer’s memory will be displayed.

How do I reset my Whirlpool Duet front load washer?

Unplug the washer for 30 seconds to attempt to reset the Duet washer control. if your fill hoses have a flood stop check valve turn the water off, disconnect the hoses and run a little water into a bucket. Then reconnect the hoses to your washer and do a Duet Washer Quick Diagnostic Test.

How do I disable Whirlpool load and go?

To disable the Load & Go™ system and use only a single dose of HE detergent, press the Load & Go™ button until the light turns off. Pour measured amount of liquid HE detergent into the single dose detergent dispenser. The detergent will dispense at the optimum time during the wash cycle.

Why does my Whirlpool washer not start?

Common solutions for: Whirlpool Washer won’t start. The timer is frequently misdiagnosed—before replacing the timer, first check all of the more commonly defective parts. If the line fuse blows, the washer won’t start. To determine if the line fuse is at fault, use a multimeter to test it for continuity.

How do I fix my washing machine not working?

Many times the solution is an easy fix or an inexpensive part.Drain Hose. When a washer leaks only during the spin cycle the likely cause is the drain hose.Fill Hose. The fill hoses could also be the culprit. Water-Inlet Valve. Too Much Detergent. Door Seal (front-load) Drain Pump. Drains and Hoses. Tub.

Why is my washer not starting?

If your washer will not start, be sure the switch is being pressed. If the lid switch is being pressed but no power is being supplied to the washers motor, then the switch is most likely bad. To test the switch, turn off power to washer and remove the wires from the lid switch.