How do you replace the control board on a Whirlpool Duet dryer?

How do I fix code f01 on my Whirlpool Duet dryer?

The Whirlpool Duet Dryer F01 error may be able to be fixed with a simple reset of the main control. Unplug the dryer for 1 minute and plug it back in this will reset the control if the error persists after that you will need to check the dryer thermal fuse. The fuse is located on top of the blower wheel housing.

How do you test a dryer control board?

How to test your dryer’s rotary switch:Unplug your dryer and remove the control console panel on the top of your dryer to locate the rotary switch.Set your multi-meter to the Rx1 setting and place the probes on the switch’s terminals. With the probes still touching the terminals, press in on and hold the switch.

When I press the start button on my dryer nothing happens?

A broken power cord, failed push-to-start switch or a bad timer can also prevent the dryer from starting. Some dryers use a motor relay to control the drive motor so a broken motor relay can prevent the dryer from starting. In electric dryers, a blown thermal fuse can keep the dryer from starting.

Why would a dryer not turn on?

Common dryer issues include a faulty door switch or start switch and control problems such as a broken dryer timer or faulty electronic control board: Problems with the door switch can prevent the dryer from starting. If the drum light doesn’t turn off, a failed door switch is the likely reason the dryer won’t start.

How do you tell if a thermal fuse on a dryer is bad?

Disconnect the two wires from the fuse and tie them together with a jumper wire, then turn on the dryer. If it runs and heats, the thermal fuse burned out and must be replaced.

Why is my Maytag dryer not starting?

On most dryers the drive motor turns the drum and the blower wheel to exhaust the air. If the dryer won’t start the motor might be defective. Before replacing the motor, check the thermal fuse, start switch and door switch because all three are more likely the cause. The dryer motor can’t be tested easily.

How do I know if my thermal fuse is blown?

To test if your thermal fuse has blown, touch the right side of your multimeter lead to the right side of the fuse, and repeat with the left multimeter lead. If the multimeter needle fails to move, this indicates the thermal fuse has blown. Learn about testing for a blown fuse.

What happens when thermal fuse blown on dryer?

A thermal fuse will blow when the temperature gets too high, not when it’s drawing too much current. When it blows, the dryer stops generating heat. It’s necessary to replace it before the dryer will run again.

Can I fix my dryer myself?

Here’s the first thing to know about dryer repair: You can solve most dryer troubles yourself. There’s no need to find a technician, schedule a service call or pay hundreds dollars for dryer repair. Tip: The first step in any appliance repair is to make sure it’s getting electricity.

Can a dryer thermal fuse be reset?

A thermal fuse is a cutoff which uses a one-time fusible link. Unlike a thermal switch which may automatically reset itself when the temperature drops, the thermal fuse is more like an electrical fuse: a single-use device that cannot be reset and must be replaced when it fails or is triggered.

Do Whirlpool dryers have a reset button?

If your Whirlpool dryer displays a “PF” error code, indicating a recent power failure, the dryer will need to be reset and restarted. This is done by pressing “Start” for a few seconds to restart the dryer. If the dryer does not restart automatically, select a new cycle and any options then press “Start” to begin.

Is there a reset button on a dryer?

Many dryers are equipped with a reset button on the control panel. If the motor won’t run, let the dryer cool for about ten minutes. Then push the reset button. If there are no problems with the motor, switches, or electrical system, this should restart the dryer.

Can I bypass thermal fuse on dryer?

Locate and Bypass the Fuse The thermal fuse will look like a thin strip of white plastic with a wire coming out of each end. In order to bypass the thermal fuse, use electrical tape to tape the two ends together. The thermal fuse will then be bypassed. Turn the dryer on to a heat cycle for no more than 90 seconds.

Can you bypass dryer thermostat?

It is possible for one of the two breakers to trip leaving the dryer 120 volts to run with but not have 240 volts to heat with. Turn each of the dryer’s breakers off and then back on. The idea would be to bypass the thermostat, hi-limit or thermal cutoff one at a time and see if the dryer will heat.

How much does a thermal fuse for a dryer cost?

Other Costs to Fix a DryerPartMaterial CostTotal CostThermal fuse$5-10$80-$130Dryer thermostat$3-20$180Bearing$50$130-$250Roller$$2301 more row

Is it worth it to fix a dryer?

If a dryer is relatively new (five years or less), having it repaired can extend its life that much longer and save money in the long run. It can be worth spending $150 – $200 to repair a midrange or high-end dryer that’s less than three years old, for example.

Why is my Whirlpool Duet dryer not starting?

An open thermal fuse or broken belt will cause the dryer not to start. It is not likely the belt broke but the thermal fuse is certainly a possibility and I am including in the images below how to access and check the thermal fuse on most Whirlpool Duet dryers. Remember to unplug the dryer first.