How do I turn off the control lock on my KitchenAid dishwasher?

How do I turn off the control lock on my KitchenAid dishwasher?

To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds. If the dishwasher has a dedicated Control Lock button in the Options selections, press and hold CONTROL LOCK for 3 seconds (press the words “Control Lock).

Are there any recalls on KitchenAid dishwashers?

There is no recall on the dishwasher, but there is a class-action lawsuit that names Kitchenaid and Kenmore, along with Whirlpool’s own name brand.

How do you unlock the control lock on a dishwasher?

On dishwasher models with a “Lock” keypad or “Control Lock” keypad, push and hold the control lock keypad for at least three seconds. Wait for the dishwasher to beep and look for the indicator light next to or above the control lock keypad. This indicates that the control lock is set.

Where is the energy saver dry pad on KitchenAid dishwasher?

Locate the wash and dry buttons on the control panel. Look for a Hi Temp scrub or wash button. Then, find a button labeled Heated Dry, Energy Saver Dry, or Air Dry.

How do you run a diagnostic cycle on a KitchenAid dishwasher?

Method one – Access the test mode by pressing the buttons on the dishwasher control panel in this sequence: “HEAT DRY, NORMAL, HEAT DRY, NORMAL”. All the lights on the display will illuminate. Press start and a test cycle should then begin which should cycle through the various functions of the dishwasher.

How do I turn off the child lock on my KitchenAid Whisper Quiet Ultima dishwasher?

To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds.

How do I turn off the child lock on my dishwasher?

To turn off the child lock on a KitchenAid dishwasher, locate the Energy Saver/Dry button. Press and hold this button for at least four seconds.

Is there a reset button on a KitchenAid dishwasher?

Control Panel Reset You can do this by pressing two buttons five times one after another total of 10 presses. Before starting this process, make sure that the door is completely shut. There are some dishwasher models that becomes reset when you press each button four times.

How do you unlock a KitchenAid double drawer dishwasher?

Press and hold the designated control lock button for your model for 3 seconds. The location of the control lock button may vary depending on your model. Refer to the Owner’s Manual for the control lock button location for your model. The light will turn off and the control will be unlocked.

How do you unlock the control lock on a KitchenAid stove?

Find the control lock button on the dishwasher’s keypad. The button responsible for the control lock varies from model to model. Hold the lock button for 3 seconds to unlock the control panel.

How do you change the control panel on a KitchenAid dishwasher?

How do I unlock my KitchenAid stovetop?

If Control Lock is activated when power to the cooktop is on, all keypads are locked out except for Power and Off. To Unlock Cooktop: Touch and hold LOCK for 3 seconds.

How do I reset my KitchenAid stovetop?

Reset power to the product:Power unit down by turning off the circuit breaker(s) for one (1) minute.Power unit up by turning on the circuit breaker(s).Start a bake cycle.Monitor the oven for one (1) minute to ensure the error code does not display again.Verify oven operation.

What is control lockout?

The Gas/Control Lockout feature disables the cooktop, locking out the control so that pressing the pads does not activate the controls. Gas flow is stopped to both the cooktop and the oven.

Why does my stove say Loc?

LOC means the control panel is locked. Per the Use and Care Guide: 1. Check that the oven and cooktop are off.

Why does my Whirlpool stove says Loc?

LOC error normally means that it is child locked. You have to press and hold one of the buttons for ten seconds depending on the model. Start by trying the ‘Start’ or ‘Cancel’ button.

What does PSH on an oven mean?

The Start pad begins any oven function. If Start is not pressed within 5 seconds, “PUSH” or “PSH” appears in the display. If start is not pressed within 1 minute after pressing a keypad, the function is canceled and the time of day is displayed.