How do I run a diagnostic on my Kenmore Elite dishwasher?

How do I run a diagnostic on my Kenmore Elite dishwasher?

Start this cycle by pressing the following buttons in this order: HEATED DRY, NORMAL WASH, HEATED DRY, NORMAL WASH. The buttons must be pushed within 5 seconds. After pushing these buttons, all the control lights will turn on and then the dishwasher will complete a short test cycle.

How do I reset my Kenmore Elite dishwasher 665?

A generic way to reset at Kenmore dishwasher is pressing the heated dry button then the normal wash button then again the heated dry then again the normal wash. After you press those four buttons in a row your dishwasher should begin a short 12 minutes test cycle during which the dishwasher will reset.

34 weitere Zeilen

Whirlpool

How old is Kenmore dishwasher model 665?

The FJ does indicate that this unit was manufactured in 1999. Most Kenmore dishwashers beginning with model number 665 will last about 15 years.

Where is the filter in my Kenmore dishwasher?

To access your dishwasher filter, remove your lower dish rack to expose the bottom of your dishwasher. The filter can be found in either a back corner of the dishwasher tub or around the base of the bottom spray arm. Many dishwasher filters are composed of two parts: an upper and lower filter assembly.

Does my Kenmore dishwasher have a filter?

Unscrew the filters located in the back of the dishwasher. The “coarse” filter traps pieces of food and removes it to another area to be disposed of during the dishwasher cycle. The “fine” filter allows the flow of water back into the cleaning cycle while keeping all other particles away.

Do dishwashers have filters that need to be cleaned?

Manual filters require cleaning at least once per month, if not more, depending on usage and pre-rinse habits. You should also be alert to visual and olfactory cues—like dishes that feel gritty, stray bits of food left behind, or unpleasant odors—to remind you to clean the filter.

How do I clean the filter on my Kenmore dishwasher 665?

2:21Suggested clip 114 secondsHow To Clean The Filter Kenmore Dishwasher – YouTubeYouTubeStart of suggested clipEnd of suggested clip

How do I clean the pump on my Kenmore dishwasher?

Unscrew the bolts on the pump housing. Then remove the pump housing from the dishwasher. Unscrew the bolt from the upper impeller. Then remove the upper impeller, followed by the food disposer blade, the spacer plate, the impeller hood, the flat plate, the O-ring and the lower impeller.

What is Smart Wash on Kenmore dishwasher?

SmartWash HE Cycle from Kenmore automatically adjusts the water and energy use to the size of the load and the amount of cleaning needed. Less water and less energy for smaller loads means more savings for you. And rest assured, it uses clean water for the final rinse.

How long is normal wash on Kenmore dishwasher?

between two to four hours

How long is the Smart Wash on a Kenmore dishwasher?

How long should a Kenmore dishwasher run? The normal cycle duration is listed at 95 minutes. I did find a service note stating that if your dishwasher is installed at the end of an un-insulated cabinet the cycle times will be longer.

Does Kenmore Elite dishwasher heat water?

Does my new Kenm3 dishwasher heat its own water? Hi Don, your dishwasher will help raise water temperature in certain cycles, however your water heater will still need to supply hot water to the dishwasher. Yes Don,however the temp boost for wash or rinse is an option you must select for each cycle.

What is smart dry on Kenmore Elite dishwasher?

SmartDry™ Technology — Dishwasher Feature Kenmore Elite and Kenmore dishwashers equipped with SmartDry™ Technology select the best drying cycle and adjust to the selected wash cycle for optimized drying performance.